Bonavita Hudson II Lifestyle Crib is a convertible piece of furniture designed to transition with your child. However, because the manufacturer (LaJobi Inc.) is no longer in business, obtaining original physical manuals can be difficult. Important Safety Note: Certain "Hudson" models with
hardware were recalled due to entrapment and suffocation risks. If your crib has a side that slides up and down, it is recommended to discard or destroy it as repair kits are no longer available. General Assembly Steps
While specific bolt lengths may vary by model year, the assembly of a Bonavita lifestyle crib typically follows these stages: Prepare the Mattress Support
: If your mattress support requires brackets, secure them with the provided wing nuts. Choose the highest position for a newborn and lower it as the child grows. Attach the Stabilizer Bar
: If applicable, insert barrel nuts into pre-drilled holes in the stabilizer bar. Align them with the bolts (often 3 1/8") and tighten using an Allen wrench. Assemble the Headboard
: Attach the headboard to the crib sides using Allen bolts and washers. Secure these through the pre-drilled holes on the bottom legs. Attach the Footboard
: Insert Allen bolts (typically 2-inch) through the inside edge of the crib sides and into the footboard. Tighten all fasteners securely with an Allen wrench. Final Inspection : Check all slats to ensure the spacing is no wider than 2 3/8 inches (6 cm) and verify there is no splintering or peeling paint. cdn.prod.website-files.com Required Tools & Hardware Allen Wrench : Usually included; often 5/32. Phillips Head Screwdriver : Required for mattress support screws and stabilizer bar. Avoid Power Tools
: Using power screwdrivers can damage the natural wood or strip the hardware. Maintenance & Safety Checklist bonavita hudson ii lifestyle crib instructions
Assembling the Bonavita Hudson II Lifestyle Crib is a straightforward process typically requiring an Allen wrench (usually included) and a Phillips head screwdriver. To ensure safety, do not use power drills or drivers, as they can damage the wood or over-tighten fasteners. Required Tools & Preparation
Tools: Allen wrench (provided), Phillips head screwdriver, and a flat head screwdriver.
Workspace: Assemble the crib on a soft surface (like carpet or the box it came in) to prevent scratching the finish.
Verification: Ensure you have all hardware, including barrel nuts, various lengths of Allen head bolts, and washers. Step-by-Step Assembly Instructions
Prepare the Stabilizer Bar: Insert a barrel nut into each pre-drilled hole in the stabilizer bar. Align them so they are ready to capture the bolts.
Connect the Side Panels: Insert 3 1/8" bolts through nylon washers into the holes and tighten into the barrel nuts using the Allen wrench. Attach Mattress Support:
Place a Phillips head screw through the stabilizer bar in the mattress support and then through the support bracket. Secure with a wing nut. Bonavita Hudson II Lifestyle Crib is a convertible
Tip: Set the mattress to the highest position for newborns and lower it as your child grows. Once they can stand, it must be at the lowest position.
Install the Headboard: Use two Allen head bolts and washers on each of the bottom legs (left and right) to secure the headboard to the crib frame. Install the Footboard:
Pre-thread four Allen head bolts into the pre-drilled holes in the bottom left and right legs of the footboard.
Insert 2-inch Allen head bolts through the inside edge of the crib sides and into the footboard. Tighten all bolts securely. Safety & Maintenance Checks
Check Stability: Gently shake the crib. It should not wobble, and all parts should be firmly attached.
Fasteners: Re-tighten all bolts to a snug fit after assembly, but do not over-tighten. Inspect them weekly for any loosening. Mattress Sizing: Use a full-size crib mattress at least
inches. The thickness should not exceed 6 inches to prevent fall hazards. Part 5: Safety Checklist (The AAP Guidelines) According
Environment: Never place the crib near windows with blind or drape cords, which present a strangulation hazard.
For additional help or replacement parts, you can check retailers like Cymax or Bed Bath & Beyond for archived PDF manuals.
Do you have all the hardware components listed, or are you missing specific bolts? Hudson 3 in 1 Convertible Toddler Bed Manual - Dream On Me
Because Bonavita Furniture (specifically the Hudson II model) has been discontinued for several years, official physical manuals are often lost. This guide covers assembly logic, safety conversion instructions, and how to obtain replacement parts.
According to the American Academy of Pediatrics and Bonavita manual:
The "Lifestyle" moniker means this crib grows with your child. Here is the breakdown of the conversion instructions.