Canon G3400 Reset Online
1. Overview: Why Reset a Canon G3400?
The Canon G3400 is a refillable ink tank printer (MegaTank). Common reset scenarios:
- Waste ink pad full → printer shows
5B00or5B01error, flashing orange/green lights. - Ink level not updating → after refilling tanks, the printer still shows low/empty.
- Network/configuration issues → forgotten Wi-Fi password, IP conflict, or settings freeze.
⚠️ Important: Resetting the waste ink counter without physically cleaning/replacing the ink absorber pads will eventually cause ink leakage and permanent damage.
Troubleshooting if reset doesn’t help
- Check ink levels and nozzles; run cleaning cycles.
- Verify USB/cable connections or router settings for network problems.
- Update or reinstall Canon drivers from Canon’s support site.
- Contact Canon support or an authorized service center for hardware errors or absorber replacements.
If you want, I can provide step-by-step screenshots or the exact button sequence tailored to your printer's region/firmware—tell me the country or model variant.
Related search suggestions provided.
To reset the Canon PIXMA G3400 (most commonly required to clear the 5B00 "Ink Absorber Full" error
or to reset the network/factory settings), you can use the procedures outlined below. комплэйс 🚨 Crucial Warning Before You Begin 5B00 error
means the physical waste ink pads (often called the "diaper" or "absorber") inside the printer are reaching capacity. комплэйс Physical Maintenance:
While resetting the counter allows the printer to work again, the ink pads are genuinely getting full. Continuing to print without eventually cleaning or replacing these pads can cause ink to overflow and leak out of the bottom of the printer. Service Mode Risk:
Do not use random, free third-party counter-reset software (like cracked "Service Tool" programs). Using incorrect software can lock your printer out of Service Mode permanently or "brick" the machine entirely. consumable.ru 🛠️ Method 1: Resetting the Ink Counter (Error 5B00)
This procedure puts the printer into "Service Mode" and uses a hardware button sequence to wipe the counter. A sheet of plain paper should be loaded into the printer. MnogoChernil Step 1: Enter Service Mode
Ensure the printer is turned off, but remains plugged into the power outlet. hold the Stop button (the red triangle in a circle). While still holding the Stop button, press and hold the Power Continue holding the Power button and release the Stop While still holding the Power button, press the Stop button 5 times
. (The indicator light will alternate between green and orange with each press). Release both buttons
. The green power light should flash a few times and then stay solidly lit. This means the printer is now in Service Mode.
(Note: If the light blinks orange or doesn't stay solid green, turn the printer off and retry the sequence very carefully). www.skclab.ru Step 2: Clear the Counter Once the printer is in Service Mode, press the Stop button 5 times Power button 1 time
The printer will print a test sheet confirming the reset or simply perform an internal mechanical action. Once it finishes and stops moving, press the Power button
again to turn off the printer. When you turn it back on, the 5B00 counter error will be cleared. MnogoChernil 🌐 Method 2: Factory & Network Reset (For Wi-Fi issues)
If you do not have a 5B00 error but simply want to wipe the network settings or return the machine's software settings to default, follow this simpler sequence: To initialize all machine settings: Turn the printer on. hold the Stop Keep holding it until the orange Alarm lamp flashes exactly
Release the button. All settings (including Wi-Fi profiles) are returned to factory defaults. Canon Knowledge Base 📋 Summary Table of Button Counts
When the printer is in Service Mode, the number of times you press the button triggers different internal actions: Number of Presses Action Triggered Service test print EEPROM information print EEPROM initialization (Counter reset attempt) Waste Ink Counter Reset (Standard method for G3400) physically access and clean
the waste ink absorber pads to prevent ink from leaking out of the bottom? canon g3400 reset
Как сбросить счётчик «памперса» для Canon PIXMA (ошибка 5B00)
How to Reset Your Canon PIXMA G3400: A Complete Guide Canon PIXMA G3400
has suddenly stopped working, flashing its orange lights or displaying the dreaded 5B00 error code
, you aren't alone. This usually happens when the internal waste ink counter (often called the "ink absorber" or "pampers") reaches its limit.
While this error sounds serious, you can often fix it yourself. This guide covers how to perform a manual reset, enter service mode, and get back to printing. Understanding the 5B00 Error
The G3400 doesn't actually have a sensor in the ink pads; it uses a mathematical counter to estimate when they are full. When it hits 100%, the printer locks down to prevent potential ink leakage. A reset clears this digital counter so you can resume printing. JustAnswer Step 1: Entering Service Mode
To perform any deep reset, you must first put the printer into Service Mode . Follow these steps precisely: the printer, but keep it plugged in. Press and hold the Stop/Cancel (red triangle) button. While still holding , press and hold the button held, and release the
(some users report 6 times works better for certain G3400 firmware) while still holding Release the button. The green light should flash and then stay steady. Step 2: Resetting the Waste Ink Counter
Once the green light is stable and the printer is in Service Mode, you can manually reset the counter:
Resetting a Canon PIXMA G3400 typically falls into three categories: a general factory reset for network issues, a manual "Service Mode" reset for the waste ink absorber error (5B00), or an ink level reset after refilling tanks. 1. Hard Factory Reset (Network & Settings)
Use this method if you are experiencing Wi-Fi connection issues or want to revert all internal settings to their original state. Initial Step: Ensure the printer is turned on.
The Process: Press and hold the Stop button (the red triangle) and release it specifically when the Alarm lamp flashes 23 times.
Result: This initializes all network settings. You will need to re-run the setup via the Canon G3400 Support Page to use the printer over a network again. 2. Resetting the Waste Ink Absorber (Error 5B00 / P07)
When the internal "ink pad" counter is full, the printer locks itself. You can often bypass this manually without software by entering Service Mode. Enter Service Mode: Turn off the printer. Hold the Stop button, then press and hold the Power button. While still holding Power, release the Stop button.
Press the Stop button 5 times (some newer firmware versions may require 6 times).
Release the Power button. The green light should flash and then stay solid. Clear the Counter:
Once the green light is stable, press the Stop button 5 times. Press the Power button once.
The printer will print a page (D=000.0) indicating the counter is reset. Turn the printer off and then back on to exit Service Mode. 3. Resetting Ink Level Notifications
If you refilled your ink tanks but the printer still warns you of low ink, you must reset the internal notification counter to prevent the print heads from running dry. Waste ink pad full → printer shows 5B00
How to reset page counter for ink absorber full (error 5B00)?
The small office hummed, or rather, it to. Sarah’s Canon G3400, a workhorse affectionately named "Old Faithful" for its unending supply of vibrant ink, had fallen silent. The LCD panel wasn't just flashing; it was panicked—an alternating blink of green and orange signaling the dreaded Support Code 5B00.
"The Ink Absorber is Full," Sarah read from her laptop screen, feeling a cold dread. She had a massive report due in two hours. Replacing the physical ink pads, she knew, was a nightmare of staining her hands for days. She needed a miracle, or at least, a reset. The Digital Escape Artist
Sarah turned to the internet. The consensus was grim: "Take it to a service center." But she didn't have time. She found whispers of a "Service Tool" software, a magical, slightly sketchy file that could bypass the printer's internal memory.
She downloaded a supposed version, but her antivirus screamed in protest. Desperate, she tried a different path—the "Manual Reset," a secret handshake between human and machine that required the precision of a safecracker. The Secret Handshake (How she did it): Turned off the G3400, keeping it plugged in. Held down the Stop (Triangle) button While holding Stop, she held the Power button
Released the Stop button (while still holding Power), then pressed Stop five times
Released the Power button. The light flashed rapidly and then settled into a solid, peaceful green. The machine was in "Service Mode." The Final Countdown
"It's just a digital trap," she muttered, her hands hovering over the buttons. She needed to tell the printer she hadn't just cleaned its 'diaper,' but replaced it. She pressed the Stop button five more times to select the reset counter function, then pressed Power once to confirm.
Old Faithful groaned, a sound of churning gears that sounded like a mechanical sigh. It didn't print, but the orange light was gone. The Revival
She turned the printer off and on again. The 5B00 error was gone. She opened her report and hit 'Print.' The printer roared to life, churning out pages, indifferent to the fact that its "absorber" was still, theoretically, full.
"Not today, service center," Sarah laughed, grabbing her report. Old Faithful had one more adventure in it, courtesy of a clever digital handshake.
Note: This story describes bypassing the physical maintenance check. The ink absorber will eventually leak if not actually replaced.
To reset a Canon PIXMA G3400 , you must first put the printer into Service Mode using a specific sequence of button presses on the control panel. This is typically done to resolve the 5B00 error, which indicates that the waste ink absorber is full. Step 1: Entering Service Mode
Before starting, ensure the printer is turned off but still plugged into a power source and that paper is loaded in the rear tray. Press and hold the Stop/Reset button (red triangle icon). While holding Stop, press and hold the Power button. Continue holding Power, but release the Stop button.
While still holding Power, press the Stop button 5 times (some models may require 6).
Release both buttons. The green power light should blink and then stay solid, indicating the printer is in Service Mode. Step 2: Resetting the Waste Ink Counter
Once the printer is in Service Mode (solid green light), use the following steps to clear the internal counter: Press the Stop button 5 times.
Press the Power button once. The printer should print a page showing the reset information (e.g., "D=000.0"). Press the Power button again to turn the printer off.
Turn the printer back on normally. The error should now be cleared. ⚠️ Important : Resetting the waste ink counter
Complete Guide to Canon PIXMA G3400 Reset: Fixing Errors & Ink Issues
The Canon PIXMA G3400 is a reliable MegaTank printer, but technical glitches like the 5B00 error (ink absorber full) or P07 error can bring your productivity to a halt. Resetting your printer is often the quickest way to resolve these issues without a costly trip to a service center.
This guide covers everything from a simple factory reset to advanced service mode procedures for ink counter issues. 1. How to Perform a Factory Reset
A factory reset is best for clearing network problems, Wi-Fi glitches, or minor system errors. Method 1: Using Printer Buttons (Button-Only Models) If your model lacks an LCD screen, use this sequence: Turn on the printer. Press and hold the Stop button (red triangle). Count the Alarm lamp flashes: 24 flashes: Resets all machine settings. 23 flashes: Resets network/Wi-Fi settings only.
Release the button once the lamp has flashed the correct number of times. Method 2: Using the Setup Menu
If your G3400 has a small display or you are using the Canon IJ Printer Utility:
Resetting your Canon PIXMA G3400 is a common maintenance task, typically required to clear the 5B00 error (full ink absorber) or to restore factory settings for network troubleshooting. How to Reset the Ink Absorber (Error 5B00)
The 5B00 error indicates that the waste ink counter has reached its limit. You can reset this manually by entering Service Mode: Enter Service Mode: Turn off the printer but keep it plugged in. Press and hold the Stop button (red triangle icon). While holding Stop, press and hold the Power button.
Release the Stop button, then press it 5 times while still holding the Power button.
Release both buttons. Wait for the green power light to stop flashing and stay solid. Execute the Reset: Press the Stop button 5 times.
Press the Power button once. The printer will reset the internal counter and may print a page showing D=000.0, confirming the reset. Turn the printer off and then back on to exit Service Mode. Factory Reset (Settings & Network)
If you need to wipe all custom settings, such as Wi-Fi configurations or passwords, use these button combinations:
Initialize Network Settings: Press and hold the Stop button until the Alarm lamp flashes 23 times, then release it.
Full Hardware Reset: Press and hold the Stop button until the Alarm lamp flashes 24 times, then release it. This restores all machine settings to their original factory defaults. Resetting After Ink Filling
If you have just refilled the ink tanks and are seeing air bubbles in the tubes, you can trigger a system-wide ink flush:
3. Network Settings Reset (Wi-Fi Restoration)
Best for: Connecting to a new router, fixing "Printer Offline" issues, or preparing the printer for sale.
If you are moving the printer to a new office or house, or if the Wi-Fi connection is corrupted, you need to wipe the network credentials.
- Turn on the printer.
- Press and hold the Wi-Fi button (looks like a signal mast) until the Wi-Fi lamp flashes.
- Press the Black button.
- Press the Wi-Fi button again.
- The Wi-Fi lamp will flash rapidly and eventually, the network settings will be initialized. The printer will return to "Access Point Mode" or default settings.
5. Common Problems & Troubleshooting
| Issue | Solution | |-------|----------| | Service Tool doesn’t detect printer | Use USB, disable antivirus, run as admin, try different USB port. | | Error 5B00 returns after reset | Absorber pads are truly full → replace physically, then reset again. | | Lights flash but no error code | Check ink levels, paper jam, or print head alignment. | | Ink reset didn’t work | Use WIC Reset Utility (paid third-party tool) as alternative. |
