Cobra 3195 Alarm Manual Full __hot__ [FREE]
Cobra 3195 is a modular alarm system typically controlled via the vehicle's original remote. While a single "full text" digital manual is rarely hosted as a plain text file, the system's operation and installation are covered by these key technical specifications and procedures: System Overview The 3195 is a CAN-bus or PLIP
(Passive Luxury Information Protocol) interface alarm. It integrates with your car's existing central locking system to arm and disarm when you lock or unlock the doors. Standard Operation
: Press the "Lock" button on your vehicle's original remote. The hazard lights will flash once, and the LED will begin to flash.
: Press the "Unlock" button on your vehicle's original remote. The hazard lights will flash twice, and the LED will stop flashing. Passive Arming
: If programmed, the system may arm itself automatically 30 seconds after the ignition is turned off and the last door is closed. Emergency Disarming (PIN Code)
If your remote fails, you can disarm the alarm using a 4-digit PIN code (found on the "Touch Panel" or your installation card):
Open the door with the mechanical key (the alarm will sound). Switch the ignition cobra 3195 alarm manual full
The LED will flash. Count the number of flashes corresponding to the first digit of your PIN. Switch the ignition and then back
Repeat for the remaining three digits. The alarm will disarm after the fourth digit is entered correctly. LED Diagnostic Signals
The LED on the dashboard communicates the cause of the last alarm trigger: : Door, boot, or bonnet opening. : Ultrasonic sensors (interior movement). : Ignition attempt. : Tamper/Power cut. Installation & Programming Highlights Ultrasonic Sensitivity
: Usually adjusted via a trimmer on the siren/control unit or via specialized programming tools. Hazard Light Connection
: Connected to the vehicle's indicators to provide visual confirmation.
: The system typically uses a battery-backed wireless or wired siren (e.g., Cobra 5100 series). Cobra 3195 is a modular alarm system typically
Common Issues
- System not arming: Check for faulty sensors, incorrect zone definitions, or low battery.
- System not disarming: Check for incorrect user code or faulty keypad.
- False alarms: Check for incorrect sensor installation or adjustment.
Button C (Auxiliary/Trunk)
- Press and Hold: Releases the trunk lock (if electronically connected) or activates the auxiliary output (e.g., garage door opener, independent lighting).
Remote Start? – Note:
The Cobra 3195 is NOT a remote start unit. It is a security and central locking system only. Do not attempt remote start wiring.
Wireless Receiver Installation
- Mount the wireless receiver in a location that provides optimal reception.
- Connect the wireless receiver to the control panel.
Part 3: Complete Programming Guide (Based on the Full Manual)
This section replicates the core instructions from the cobra 3195 alarm manual full. These steps assume you have a working Master Valet Switch (usually a small black button hidden under the dashboard) and at least one working remote.
Problem 2: Remotes work but engine won’t start.
Fix: The immobilizer is still active. Insert key, turn ignition ON, press disarm button. If still no start, use valet button: Turn ignition ON, press valet button for 4 seconds until LED turns off.
Final Note
The above guide is a summary intended to give you a functional understanding of the Cobra 3195 alarm system without reproducing copyrighted text from the official manual. For detailed wiring diagrams, regulatory compliance information, or advanced configuration (e.g., integrating with third‑party home‑automation platforms), you should obtain the full, up‑to‑date manual from the sources listed in section 9.
The Cobra 3195 is a vehicle security system, part of the modular 3100 series (similar to the Cobra 3198). It features perimetric protection (doors, hood, trunk), volumetric ultrasonic interior sensors, and an engine immobilizer. Core Operations
Arming: Press the large button on the remote. The turn indicators flash twice and the LED begins to flash. System not arming : Check for faulty sensors,
Disarming: Press the large button again. The turn indicators flash once.
Passive Arming: If enabled, the system automatically arms 30 seconds after the ignition is switched off and the last door is closed.
Sensor Bypass: To arm the system without interior sensors (e.g., if leaving a pet inside), press the arming button twice within a short window. Programming New Remotes
To pair a new key fob, you typically need the system's unique 4-digit PIN code:
Press and hold both buttons on the remote for 10 seconds until the LED stays on.
Turn the ignition ON and OFF 3 times within 7 seconds; the dashboard security LED will light for 3 seconds.
Enter the PIN by counting the security LED flashes for each digit, turning the ignition OFF/ON between each number.
Once the PIN is accepted, press the large button on each remote to be paired. Emergency Override If your remote fails, you can disarm the system manually: Cobra Alarm Fob Programming Guide | PDF - Scribd
