I Download Fixed Driver Cutting Plotter Jinka 1351 _top_ May 2026

To fix driver issues for your Jinka 1351 cutting plotter, it is essential to use a verified driver compatible with your specific hardware version (e.g., the standard JK1351 vs. the XL Pro models). 1. Download Links

You can find the correct driver files through the Jinka Indonesia Download Center, which provides specific links based on the plotter type: Jinka XL PRO 1351 (Only Cut): Google Drive Link. Jinka JK/XL Series (Standard): General Download Folder.

Jinka 1351PE: Specific 32-bit/64-bit drivers are often required for newer Windows versions. 2. Installation Steps

For a "fixed" installation that avoids common errors, follow this procedure:

Extract Files: Download the ZIP and use a tool like WinRAR to extract the setup.exe.

Run as Administrator: Right-click the setup.exe and select Run as Administrator to prevent registry permission errors.

USB Signature (Windows 10/11): If the driver fails to install, you may need to disable Driver Signature Enforcement through Windows Advanced Startup.

Connect & Power On: Connect the USB cable and turn on the plotter only after the driver installation prompts you. 3. Port & Communication Fixes

If the machine is installed but not cutting, check these settings:

Device Manager: Look under Ports (COM & LPT). The plotter should appear as "USB Serial Port" or "JINKA USB PRINT".

COM Port Settings: For optimal performance, assign the plotter to COM2 or COM3.

Port Configuration: Ensure the following values match in both Windows and your cutting software (like CorelDraw or Flexi): Bits per second: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: None. LINK DOWNLOAD • Welcome to JINKA Indonesia

Core Feature:

• Communication Bridge: The primary feature of this driver is to establish a stable connection between the Jinka 1351 hardware and the Windows Operating System (enabling the computer to recognize the cutter).

Key Capabilities Enabled by the Driver:

• USB Connectivity: Allows for data transmission via USB port, which is standard for the 1351 model.
• Plotter Control: Enables the software (such as ArtCut, FlexiSign, or SignMaster) to send commands to the plotter, including:
  • Cutting Speed Adjustment: Control over how fast the blade moves.
  • Pressure/Force Adjustment: Control over how hard the blade presses down.
  • Origin Point Setting: Defining where the blade starts cutting.
• Page Size Recognition: Allows the software to recognize the 1351's specific cutting width (approx. 1350mm / 53 inches).

"Fixed" Driver Context: If you specifically downloaded a "fixed" driver, the feature usually implies:

• Bug Fixes: Resolves issues where the plotter would previously cut distorted shapes or stop mid-cut.
• OS Compatibility: Enables the plotter to work on newer versions of Windows (like Windows 10 or 11) where older drivers failed.
• Port Conflict Resolution: Fixes issues where the computer could not assign the correct COM/USB port to the device.

Downloading and installing the "fixed" or correct driver for the Jinka 1351

cutting plotter is essential for ensuring your computer can communicate with the hardware without errors

. Below is a guide on how to properly locate, install, and configure this driver. 1. Locate the Correct Driver

Ensure you download a driver specific to your model variant (e.g., standard, Pro, or semi-auto contour cut) to avoid compatibility issues. Official Sources : Highly recommended to use the Jinka Indonesia Support Page

which hosts dedicated folders for various models, including the Variant Selection Jinka Pro 1351 (Standard) : For models that only perform standard cutting. Jinka Pro 1351 SA : For models supporting semi-auto contour cutting. Plugin Alternatives : For those using CorelDRAW, specialized plugins like are available specifically for the 2. Installation Process

Once you have the correct file, follow these steps for a "clean" installation: Run as Administrator : Right-click the file and select Run as Administrator to prevent registry permission errors. Manual Port Assignment

: During the setup, choosing "Manual Setup" instead of "Auto-Detect" is often more reliable. It is recommended to assign the plotter to

to avoid conflicts with other USB devices or Bluetooth adapters. Verification : After installation, open the Device Manager and check under Ports (COM & LPT)

to ensure "JINKA 1351" or "USB Serial Port" appears without warning symbols. 3. Port and Communication Settings i download fixed driver cutting plotter jinka 1351

Most "driver issues" are actually configuration errors in the port settings. For a stable connection, use the following Serial Port Properties Bits per second Flow control

: None (This is critical for preventing "cutting in wrong places" or "chewing up" material). 4. Software Setup

After the driver is installed, your cutting software (like FlexiSign, Artcut, or SignTools) must be pointed to the correct device: Device Selection : In your software's setup menu, select Jinka 1351 from the dropdown list. Connection Method

: If using a USB-to-Serial connection, ensure the software is set to Direct COM Port

rather than "USB" if the driver was installed as a virtual serial port. SignTools 4 or adjust the blade offset once your driver is connected? Driver Jinka 1351 28 - Facebook

To successfully download and install the fixed driver for the Jinka 1351 cutting plotter

, you should use verified links from the manufacturer or recognized technical support pages. Official Download Links

Depending on your specific 1351 sub-model, use these official repositories from Jinka Indonesia Jinka JK/XL (Only Cut): Google Drive Link Jinka XL Pro V (Auto Contour): Google Drive Link Alternative CorelDRAW Plug-in: You can also find specialized software like PlotCalc for Jinka XE-1351 for direct design integration. Installation Steps Extract Files:

Once downloaded, use a tool like WinRAR to extract the folder. Run Setup: in the extracted folder and run it. Connection: Connect your plotter via

. If using USB, Windows should ideally recognize it as a new "USB Serial Port" or "JINKA USB PRINT" in the Device Manager Ports (COM & LPT) Software Configuration:

Open your cutting software (SignMaster, Artcut, or CorelDRAW). Jinka 1351

(or Jinka-ARMS V3 depending on the model) as your output device. Set the connection method to Direct COM Port Direct USB Port as appropriate. Troubleshooting Driver Jinka 1351 28 - Facebook

Establishing a functional connection for a Jinka 1351 cutting plotter depends heavily on matching the specific hardware variant—such as the standard or the

—to its corresponding driver and operating system. Because these machines often use FTDI USB-to-serial chips, a "fixed" driver typically refers to a version that correctly maps the USB port to a virtual COM port that cutting software like FlexiSign, SignMaster, or CorelDRAW can recognize. Essential Setup and Driver Installation To successfully install a stable driver for the Jinka 1351 , follow these technical steps:

Download the Correct Variant: Ensure the driver matches your specific model's capabilities. For example, a standard Jinka 1351 requires a different driver than the Jinka 1351 Semi-Auto Contour Cut

Administrative Execution: Extract the downloaded ZIP file and right-click the setup.exe or install.exe to Run as Administrator. Skipping this can lead to registry errors that prevent the plotter from appearing in your software's port list.

Port Assignment: Once installed, reconnect the USB. In your cutting software, look for the Direct USB Port or a specific COM port (often COM3 or COM4) assigned to the device. Troubleshooting Common Connection Failures

Even with the "fixed" driver, certain hardware and software conflicts can interrupt the cutting process: Driver Jinka 1351 28 - Facebook

Issue D: You Have a Clone, Not a Genuine Jinka

Many plotters labeled "Jinka 1351" are actually rebranded Redsail or Creation units. Try the universal SignMaster Cutter Driver or the Windows Built-in "Generic Text/Only" driver modified for HPGL.

The "Cable Fix"

Believe it or not, 70% of Jinka 1351 issues are USB cable quality. Use a USB 2.0 Printer Cable (not USB 3.0) that is shorter than 3 meters. The Jinka’s mainboard is sensitive to voltage drop.

Final Verdict

Don't throw your Jinka 1351 in the trash. The hardware is fine—the software is just stupid. Once you force-feed Windows the correct generic USB driver, this plotter is a beast.

Have you fixed a Jinka 1351 driver issue? What software are you using (SignMaster, Sure Cuts A Lot, Easy Cut Studio)? Drop a comment below—I know how lonely this troubleshooting gets. To fix driver issues for your Jinka 1351

Disclaimer: Always scan downloaded driver files with Windows Defender before installing. I am not affiliated with Jinka.

To download and install the "fixed" driver for your Jinka 1351 cutting plotter

, you should primarily use the official resources provided by the manufacturer or authorized distributors to ensure compatibility and stability. Driver & Software Download Links The most reliable source for Jinka drivers is the Jinka Indonesia Support Portal

, which provides direct Google Drive links for various models: Jinka JK/XL Type (Only Cut): Direct Download Link for standard cutting drivers. Jinka XL Pro V (Auto Contour): If your 1351 has auto-contour features, use this Specific Driver Link CorelDRAW Plug-in: For users needing to cut directly from CorelDRAW, the PlotCalc Plug-in supports the Jinka XE-1351. Critical Installation Fixes

Many "driver issues" with the Jinka 1351 are actually configuration errors. Follow these steps to "fix" a non-responsive plotter: USB-to-Serial Driver: Most Jinka plotters use the

chip for USB communication. If Windows does not recognize the device, download and install the CH341SER.EXE driver from the chip manufacturer. COM Port Settings: Port Selection:

Ensure your software (Flexi, SignMaster, or AnyCut) is set to the same COM port as seen in Windows Device Manager (often works best). Flow Control: In your COM port settings, set Flow Control to "None" (Xon/Xoff is often the default but causes errors). Baud Rate: Set the speed to for stable communication. Physical Connection:

Always try different USB ports on your computer if the plotter is not detected initially. Nanjing Qinheng Microelectronics Co., Ltd. Compatible Software Options

If the basic driver does not work, these professional software packages include "fixed" internal drivers for Jinka models: SignMaster / AnyCut:

These are often bundled with Jinka machines and include built-in calibration tools for the 1351. SignCut Pro: Offers a dedicated support page for Jinka Driver Integration

A modern plug-in for both Adobe Illustrator and CorelDRAW that supports Jinka plotters on Windows 11. SignCut Pro set up contour cutting for this specific model? Software for JinKa XE-1351 plotter - PlotCalc

Here’s a product-style review based on your search query for a fixed driver for the Jinka 1351 cutting plotter:

Title: Fixed driver finally made my Jinka 1351 usable again
Rating: ★★★★☆ (4/5)

I was struggling for weeks with driver conflicts on my Jinka 1351 cutting plotter – constant communication errors, weird offsets, and the machine either not cutting or randomly stopping mid-job. After downloading what’s labeled as the “fixed driver” (likely from a support forum or alternate source), the difference was night and day.

Pros:

• Installation was straightforward after removing the old driver completely.
• The plotter now connects reliably via USB/COM port without dropping signal.
• Cutting accuracy improved significantly – no more drifting contours or skipped lines.
• Works with SignMaster, Flexi, and ArtCut (tested on Windows 10).

Cons:

• The “fixed driver” isn’t officially hosted on Jinka’s main site (had to dig through user shares).
• No digital signature – Windows Defender flagged it, but I confirmed it was clean.
• Still requires manually setting the correct port baud rate (9600 or 115200 depending on firmware).

Verdict: If your Jinka 1351 is acting up with generic drivers, this fixed version is a lifesaver. Just make sure to scan the file, disable driver signature enforcement during install (Windows 10/11), and reboot after. Recommended for anyone stuck with a non-responsive plotter.

How to Download and Install Fixed Drivers for the Jinka 1351 Cutting Plotter

If you are a sign maker or a DIY enthusiast, the Jinka 1351 is a workhorse. However, many users run into a common roadblock: connection issues caused by outdated or corrupt drivers. If your computer isn’t recognizing your plotter, or if it stops mid-cut, you likely need to download the fixed driver for the Jinka 1351.

This guide will walk you through finding the correct software, installing it properly, and getting your machine back to work. Why Do You Need a "Fixed" Driver?

The Jinka 1351 typically uses a USB-to-Serial CH340 or FTDI chip to communicate with your PC. Problems usually arise because:

Windows Updates: New Windows versions often override older drivers with "generic" versions that don’t work.

Driver Signature Enforcement: Windows 10 and 11 often block unsigned drivers. Communication Bridge: The primary feature of this driver

Port Conflicts: The software is looking for COM1, but your USB is plugged into COM3.

A "fixed" driver is simply the stable, verified version of the USB-to-Serial driver that ensures a steady handshake between your cutting software (like AnyCut, CorelDraw, or Artcut) and the hardware. Step 1: Where to Download the Jinka 1351 Driver

To get your Jinka 1351 running, you don't actually look for a "Jinka" brand file; you look for the USB Serial Driver.

Official CH340 Driver: Most Jinka models use the CH341SER chip. You can download the latest stable version from the official manufacturer (WCH) or your distributor's support page.

Legacy Drivers: If you are on an older system (Windows 7 or XP), you may need the specific PL2303 Prolific driver.

Note: Always download drivers from reputable sources to avoid malware. If your plotter came with a small blue or white CD, the files are there, but downloading the latest version online is usually better for Windows 10/11 compatibility. Step 2: Installation Guide (The "Fix") Before installing, unplug the USB cable from your computer.

Run as Administrator: Right-click the downloaded setup file and select "Run as Administrator."

Click Install: Follow the prompts. If it says "Driver is pre-installed," that’s a good sign.

Restart Your PC: This is a crucial step that many skip. Restarting clears the port registry.

Plug in the Plotter: Turn on your Jinka 1351 and plug in the USB cable. Step 3: Configuring the COM Port (Crucial)

Even with the driver installed, the Jinka won't cut if the ports don't match. Right-click the Start button and open Device Manager. Look for Ports (COM & LPT).

You should see USB-SERIAL CH340 (COMX). Note the number (e.g., COM3). Open your cutting software (Artcut, SignMaster, etc.).

In the Link/Output Settings, change the Port to match the one in Device Manager (e.g., COM3).

Set the Baud Rate to 9600 (this is the standard speed for Jinka 1351). Troubleshooting Common Jinka 1351 Issues 1. The "USB Device Not Recognized" Error

Try a different USB port, preferably one on the back of the PC (if using a desktop). Avoid using USB hubs, as they often don't provide enough voltage for the data transfer. 2. Plotter Stops Mid-Cut

This is often static electricity or a "buffer overflow." Ensure your plotter is grounded (the Jinka 1351 is a large metal machine and builds up static). Also, ensure you are using a high-quality, shielded USB cable. 3. Driver Fails to Install on Windows 11

You may need to temporarily disable "Driver Signature Enforcement." Go to Settings > Recovery > Advanced Startup, then navigate to Startup Settings and press F7 to disable the enforcement. Conclusion

Downloading the fixed driver for the Jinka 1351 is the first step toward flawless vinyl cutting. By ensuring you have the CH340 USB-to-Serial driver and matching your COM port settings, you can eliminate 90% of the technical headaches associated with this machine.

For Windows Users:

1. Visit the Official Website: Go to the official Jinka (or the manufacturer's) website. Look for a "Support" or "Downloads" section.

2. Search for Your Model: Use the search function on the website to find drivers for the Jinka 1351.

3. Select Your Operating System: Make sure to select the correct version of Windows you're using.

4. Download the Driver: Click on the driver download link. The file might be in a .zip or .exe format.

5. Extract and Install: If the file is zipped, extract it to a folder. Run the .exe file and follow the installation prompts.

6. Connect Your Plotter: Plug your Jinka 1351 into your computer using the appropriate cable (usually USB).

7. Test the Installation: Open a design or cutting software (like Adobe Illustrator or CorelDRAW) to test if your plotter is recognized and functional.