Jungheinrich Etv 216 Error Codes link Now

This model is part of Jungheinrich’s reach truck family. Error codes typically appear on the display (often a multi-line LCD or, on older models, a flashing LED/blinking sequence).

How to Perform a "Soft Reset" (Clear Stored Codes)

You don't always need a laptop. If the truck is beeping but still moves, try this procedure:

Park safely on level ground. Lower the mast completely.
Turn the key to Off (Position 0).
Unplug the battery connector.
Wait 60 seconds (this drains residual CAN-bus voltage).
Plug the battery back in.
Turn the key to On (Position 1).
Result: Non-critical errors (e.g., momentary sensor glitches) should clear.

If the code returns immediately – you have a hardware problem, not a ghost in the machine.

8. L211 – Right Side Light Failure (LED)

Meaning: The CAN-based LED light cluster on the right side is not responding. jungheinrich etv 216 error codes

Symptoms: Turn signal or tail light not working. No bulb-out warning on older systems.

Causes:

Failed LED driver module inside the light.
Water intrusion in the light housing.

Solution:

Swap left and right lights to isolate the problem.
If the fault follows the light, replace the entire LED assembly (non-serviceable).

How to Read Codes on the ETV 216

Unlike older units with LED blinks, the ETV 216 typically uses the Jungheinrich CANcode system displayed on the onboard screen.

Example format: F1 23 or E 12
F = Fault (Functional error – machine may be derated)
E = Error (Severe – truck may be disabled)

To access stored codes:

Turn the key to position "I" (ignition on, truck not driving).
Press and hold the diagnostic button (usually located on the dash panel or under the display).
Scroll through the active or history log.

Step 5: CAN Bus Errors (E2210, E2211)

Common on ETV 216 due to steering wheel flexing.
Inspect wiring where harness passes through the mast tilt joint – frequent break point.
Check terminating resistors (120Ω between CAN-H and CAN-L at ends of bus).

The CanDis Display

Most ETV 216 models are equipped with a CanDis (CANbus Display). Under normal conditions, it shows battery status, operating hours, lift height, and weight. When an error occurs, the display switches to a hexadecimal or decimal code format. This model is part of Jungheinrich’s reach truck family

8. Code: E 21 (Emergency Stop Circuit Open)

Symptoms: Truck completely dead, no hydraulic or drive function.
Cause: E-stop button physically pressed, wiring fault, or damaged safety relay.
Fix: Rotate all emergency stops (there are two: on the dash and on the tiller arm). If not resolved, check continuity of the safety loop through the seat switch and e-stop contacts.

Part 5: Preventive Maintenance to Avoid Error Codes

The best way to deal with error codes is to prevent them. Based on fleet data from 200+ ETV 216 units, follow this PM schedule:

| Interval | Action | Codes Prevented | |----------|--------|------------------| | Daily | Check battery water level (lead-acid) and charge algorithm | 121 04, 121 14 | | 500 hours | Replace hydraulic return filter | 313 01, 442 05 | | 1000 hours | Re-grease steering kingpin and reach carriage rollers | 672 08, 455 12 | | 2000 hours | Replace lift chain and check limit switch cam alignment | 455 05 | | Annually | Calibrate pedal sensors and steering angle | 024 10, 672 03 | | As needed | Update FGC firmware (Jungheinrich bulletin 2021-R02 fixes spurious 174/313 codes) | Random intermittent codes |

Quick Reference: Error Code Reset Table

Jungheinrich Etv 216 Error Codes __link__ Now