Nako Na-613d Disable Alarm ~repack~ May 2026
To disable the alarm on the Nako NA-613D digital clock, you need to use a specific button combination to toggle the alarm status icon on the display. How to Disable the Alarm Hold "S" (Set) : Press and hold the Press "D" (Date/Adjust) : While still holding the button, press the Check the Display
: Look for the small alarm icon (usually looks like a bell or a "wave" symbol). If the icon is , the alarm is If the icon disappears , the alarm is Repeat if needed
: If you also want to toggle the hourly chime (a small "beep" every hour), repeat the same combination ( Hold S + Press D
) until all icons disappear from the alarm/chime section of the screen. Summary of Button Functions : Cycles through Time, Alarm Set, Stopwatch, and Time Set.
: Used to select which digit to change (hours/minutes) and to view the alarm time. D (Date/Adjust)
: Increases the value of the flashing digits or displays the date when in normal time mode. or setting a new alarm time Nako NA-613D инструкция часов
I’m unable to generate a technical or investigative report on the specific phrase “nako na-613d disable alarm” because it does not correspond to any known standard product, system, software, or widely documented process. nako na-613d disable alarm
Here’s why, and what you can do instead:
4. Remove power (if silence fails)
- If battery-powered: twist or unclip the detector from its base and remove the batteries. Wait 30 seconds, then replace batteries and reattach.
- If hardwired with battery backup:
- Turn off the circuit breaker for that circuit.
- Twist or unclip the detector and remove backup batteries.
- Wait 30 seconds, reinsert batteries, and restore power.
- If fully hardwired and you cannot access breaker safely, call an electrician.
Step 1: Identify the Admin Number
The Nako NA-613D must have your phone number pre-set as the admin. If you haven’t set one, the first authorized number to contact the tracker becomes admin by default.
What you need:
- Small Phillips screwdriver
- Tweezers
- Electrical tape (optional)
Conclusion
Disabling the alarm on the Nako NA-613D is straightforward once you know the correct SMS commands or app settings. For most users, sending 123456 alarm off via SMS will instantly silence excessive beeping while retaining GPS functionality. If that fails, escalate to the configuration tool or hardware modification—but always weigh the security trade-off.
Remember: A silenced alarm should not mean a disabled tracker. Keep critical alerts like SOS and low battery active in SMS form for safety.
Have questions about your Nako NA-613D? Leave a comment below or consult your device manual. Always test alarms in a safe environment before relying on them for security.
To disable the alarm on a Nako NA-613D Go to product viewer dialog for this item. To disable the alarm on the Nako NA-613D
digital clock, you typically use a combination of the "S" and "D" buttons while in the normal time-display mode. This compact device is widely used as a car dashboard clock or kitchen timer and is available at retailers like Meesho and Amazon India. Quick Method to Disable the Alarm
If you are in the normal mode (the screen showing the current hour, minute, second, and day of the week), follow these steps to toggle the alarm off:
Press and hold the "S" button. While holding it, the current alarm time will be displayed. Simultaneously press the "D" button.
Check the display icon. Look for a small bell or "ALM" icon on the screen. If the icon disappears, the alarm is disabled. If it reappears, it is enabled. Managing the Hourly Chime
Often, users mistakenly believe the alarm is on when they actually hear an hourly beep. To disable the hourly chime: Press and hold the "S" button. Simultaneously press the "M" button.
Observe the week indicator. Usually, if all the week icons (MON–SUN) appear or disappear, it indicates the hourly chime has been toggled. Setting or Changing the Alarm Time If battery-powered: twist or unclip the detector from
If you need to adjust the alarm before turning it off, use the mode button to navigate: Enter Alarm Mode: Press the "M" (Mode) button two times.
Select Digits: Press the "S" button to toggle between flashing hour and minute digits.
Adjust Values: Press the "D" button to increase the flashing numbers to your desired time.
Save and Exit: Press the "M" button once more to return to the normal time display. Troubleshooting Common Issues
The alarm still rings: Ensure the alarm icon is completely gone from the LCD. Sometimes the "ALM" text is very small and easy to miss. Buttons aren't responding : Check the battery. The
typically uses a single button cell or AAA battery depending on the specific sub-model variant.
Screen is faint: This device is not waterproof; moisture or low battery life can cause the display to fade or the alarm to malfunction. Nako NA-613D Plastic Quartz Clock for Car (Black, Small)
1. Prepare
- Have a ladder or stable step stool to reach the unit.
- If hardwired, turn off power at the circuit breaker before touching the detector.
- Keep a flashlight and gloves handy.