This website uses cookies. By continuing to use the website you consent to the use and storage of cookies on your device.

Official Wiko Kite 4g L4020 Stock Rom Install May 2026

Guide to Installing Official Wiko Kite 4G (L4020) Stock ROM If your Wiko Kite 4G is experiencing software glitches, stuck in a boot loop, or you simply want to return to a clean "factory fresh" state, installing the official stock ROM (firmware) is the most effective solution. This process overwrites the existing system software with the original manufacturer version. Prerequisites Before You Begin

Before starting the installation, ensure you have the following ready to avoid any interruptions:

Backup Your Data: This process will completely wipe your phone’s internal storage. Save your photos, contacts, and messages. Battery Level: Ensure your device has at least 50% charge. USB Cable: Use a high-quality or original micro-USB cable.

Windows PC: The flashing tools required are designed for Windows environments. Step 1: Download Required Files

You will need three specific components to successfully flash the Wiko Kite 4G (L4020):

Official Wiko Kite 4G Stock ROM: Ensure you download the version specifically for the L4020 model.

Broadcom USB Drivers: Since the Kite 4G uses a Broadcom chipset, these drivers allow your PC to communicate with the phone in "Download Mode."

Wiko Download Tool: Wiko usually provides a dedicated "all-in-one" executable (.exe) tool for their legacy devices, or you may need the Broadcom MultiDownloader tool. Step 2: Install the Drivers Extract the downloaded USB Driver package.

Right-click on the setup file and select Run as Administrator.

Follow the prompts and restart your computer once the installation is complete. Step 3: Flash the Stock ROM

Wiko typically provides a user-friendly installation tool for the Kite 4G. Follow these steps:

Launch the Tool: Open the Wiko L4020 installation software you downloaded.

Prepare the Phone: Power off your Wiko Kite 4G completely. Do not connect it to the PC yet.

Start the Process: Click the Download or Start button within the software interface.

Connect the Device: While the phone is powered off, press and hold the Volume Down (or sometimes both Volume buttons) and connect the USB cable to your PC.

Flashing Progress: The tool should recognize the device, and a progress bar will appear. It will turn from gray to yellow or green as the firmware is written to the device.

Completion: Once the bar reaches 100% or a "Download OK" message appears, you can safely unplug the phone. Step 4: First Boot official wiko kite 4g l4020 stock rom install

The first boot after a fresh ROM installation takes longer than usual (typically 5–10 minutes). Do not force restart the device during this time. Once the "Welcome" screen appears, you can proceed with the standard Android setup. Troubleshooting Common Issues

Device Not Recognized: Try a different USB port (preferably a USB 2.0 port) or a different cable. Ensure the Broadcom drivers are correctly installed in the Device Manager.

Stuck at 0%: Disconnect the phone, remove and re-insert the battery (if possible), and try the button combination again before plugging it back in.

Verification Failed: Ensure the ROM file you downloaded is not corrupted and is specifically for the L4020.

Disclaimer: Flashing firmware carries risks. Ensure you follow the steps carefully. We are not responsible for any damage to your device.

Installing the official stock ROM on a Wiko Kite 4G (L4020) can be a bit tricky, but it's doable with the right guidance. Here are the general steps to help you through the process:

Warning:

  1. Backup your data: Before you start, make sure to backup your important data, as the installation process will erase all data on your device.
  2. Use at your own risk: This process is done at your own risk. If something goes wrong, you might brick your device.

Required files and tools:

  1. Stock ROM: You'll need the official stock ROM for Wiko Kite 4G (L4020). You can try searching for it on the Wiko website, XDA Developers forum, or other reputable Android forums. Make sure it's the correct version for your device.
  2. SP Flash Tool: This is a popular tool for flashing stock ROMs on Android devices. Download the SP Flash Tool from a reputable source (e.g., MediaTek's official website or XDA Developers).
  3. USB driver: You'll need a USB driver to connect your device to your computer. You can download the Mediatek USB driver or the Wiko USB driver.

Step-by-Step Instructions:

  1. Prepare your device:
    • Charge your device to at least 50% battery level.
    • Enable Developer Options on your device: Go to Settings > About phone > Build number (tap 7 times).
    • Enable USB Debugging: Go to Settings > Developer options > USB debugging.
  2. Install the USB driver:
    • Connect your device to your computer using a USB cable.
    • Install the Mediatek USB driver or the Wiko USB driver.
  3. Download and extract the stock ROM:
    • Download the stock ROM for Wiko Kite 4G (L4020) and extract it to a folder on your computer.
  4. Download and launch SP Flash Tool:
    • Download SP Flash Tool and extract it to a folder on your computer.
    • Launch SP Flash Tool (e.g., "flash_tool.exe").
  5. Configure SP Flash Tool:
    • In SP Flash Tool, click on the "Scatter-loading" button and select the scatter file from the extracted stock ROM folder (usually named "MT6580M_scatter.txt" or similar).
    • Make sure the "DA File" field is set to "MTK_All_In_One_DA" (or similar).
  6. Select the firmware:
    • In SP Flash Tool, select the firmware components to flash (e.g., "Android", "Boot", "Recovery", etc.). You can usually select all components.
  7. Connect your device:
    • Connect your device to your computer using a USB cable.
    • SP Flash Tool should detect your device.
  8. Flash the stock ROM:
    • Click on the "Download" button in SP Flash Tool to start the flashing process.
    • Wait for the process to complete. This may take a few minutes.
  9. Reboot your device:
    • Once the flashing process is complete, disconnect your device from your computer.
    • Reboot your device.

Post-installation steps:

  1. Perform a factory reset: After flashing the stock ROM, it's recommended to perform a factory reset to ensure a clean boot.
  2. Setup your device: Follow the on-screen instructions to set up your device.

To install the official stock ROM on your Wiko Kite 4G (L4020), you will primarily use the SP Flash Tool, as this device runs on a MediaTek chipset. This process will wipe all data on your phone, so ensure you have backed up your important files. Pre-requisites

Wiko Kite 4G (L4020) Stock ROM: You can find the firmware file on Google Drive or from the official Wiko support site.

MediaTek USB VCOM Drivers: Required for your computer to recognize the phone in "Preloader" mode.

SP Flash Tool: The official utility used to flash firmware onto MediaTek devices.

USB Cable & PC: A stable connection is vital to avoid "bricking" the device. Installation Steps

Install Drivers: Install the MediaTek VCOM drivers on your PC. You may need to disable "Driver Signature Enforcement" on Windows 10/11 for them to install correctly. Guide to Installing Official Wiko Kite 4G (L4020)

Extract Firmware: Unzip the downloaded Stock ROM folder. Inside, you should see a file named something like MT65xx_Android_scatter.txt. Setup SP Flash Tool:

Open the SP Flash Tool folder and run flash_tool.exe as an administrator.

In the Download tab, click on Scatter-loading and select the scatter file from your extracted ROM folder. Configure Flashing:

Ensure all partitions (Preloader, Recovery, System, etc.) are checked. Select Download Only from the drop-down menu.

Note: Only use "Firmware Upgrade" if the "Download Only" mode fails. Start Flashing: Click the Download button (green arrow) in the tool. Power off your Wiko Kite 4G.

Connect the phone to the PC via USB while holding the Volume Down or Volume Up button to trigger the connection.

Completion: A progress bar will appear. Once finished, a green circle or "Download OK" message will pop up. Disconnect your phone and power it on. Troubleshooting

Not Detecting: If the PC doesn't see the phone, try a different USB port or reinstall the VCOM drivers.

Boot Loop: If the phone hangs at the Wiko logo after flashing, boot into Recovery Mode (Volume Up + Power) and perform a "Wipe Data/Factory Reset."

Are you experiencing a specific error like a boot loop or a "PMT changed" error in SP Flash Tool that I can help you resolve? Official Wiko Kite 4G L4020 Stock Rom - Google Drive

🖱️ Official Wiko Kite 4G L4020 Stock Rom - Google Drive. Google Docs

Installing the official stock ROM on your Wiko Kite 4G (L4020)

is the primary method for fixing software issues like boot loops, system lag, or "bricked" states. This process replaces your current operating system with the factory-stable version provided by Wiko. Essential Preparation

Before starting, ensure you have the following prerequisites ready:

Battery Level: Charge your device to at least 80-85% to prevent it from shutting down mid-process.

Backup: Flashing a stock ROM erases all personal data, including photos and contacts. Backup your data : Before you start, make

Hardware: Use a high-quality USB data cable and a Windows-based PC.

IMEI Note: Keep your original IMEI number handy, as you may need to restore it using an IMEI tool after flashing. Required Downloads Stock ROM Firmware: Download the specific

firmware. You can often find official versions on the Wiko Mobile Support page by entering your device's IMEI.

VCOM Drivers: Install the MediaTek (MTK) USB Drivers so your computer can recognize the phone in "Download Mode".

Flash Tool: Most Wiko devices with MTK chipsets use the SP Flash Tool. Installation Steps

Extract Files: Unzip the downloaded firmware and flash tool into separate folders on your desktop.

Launch Flash Tool: Open the SP Flash Tool folder and run flash_tool.exe as an administrator.

Load Scatter File: In the tool, click on the Scatter-loading button and navigate to your extracted firmware folder to select the file ending in .txt (usually named something like MTxxxx_Android_scatter.txt).

Select Mode: Ensure the dropdown menu is set to Download Only to avoid wiping critical bootloader partitions unless necessary. Initiate Flash: Click the Download button in the tool. Connect Device: Power off your Wiko Kite 4G

completely. While holding the Volume Down or Volume Up button, connect it to your PC via USB.

Monitor Progress: A yellow progress bar will appear. Once finished, a green ring or "Download OK" message will pop up.

Reboot: Disconnect the phone and power it on. The first boot can take 5–10 minutes as the system initializes. Troubleshooting Tips

Not Recognized: If the PC doesn't detect the phone, try a different USB port or re-install the VCOM drivers.

Error Messages: If you get a "PMT changed" error, you may need to switch the flash tool mode from "Download Only" to Firmware Upgrade. Download Wiko Stock ROM for all models (Latest Firmware)

Preparatory steps

  1. Verify exact model number: Wiko Kite 4G L4020. Confirm hardware matches the ROM package.
  2. Download the official stock ROM for L4020 from a trusted source (Wiko support or verified forum). Do not use ROMs for other models.
  3. Download and install required USB drivers on your PC. Reboot after installation.
  4. Extract the ROM package and the flash tool to a simple folder (e.g., C:\Wiko).

Step 3: Load the Scatter File

  1. In SP Flash Tool, click the Download tab.
  2. Click the Scatter-loading button (usually on the right side).
  3. Navigate to the folder where you extracted the Stock ROM files.
  4. Select the file named MT6735_Android_scatter.txt (the name may vary slightly depending on the specific ROM version).
  5. The tool will populate a list of files (PRELOADER, PRO_INFO, BOOT, etc.).

Troubleshooting:

  • Error: “STATUS_BROM_CMD_SEND_DA_FAIL” → Reinstall VCOM drivers or try a different USB port (use USB 2.0 if possible).
  • Error: “S_BROM_DOWNLOAD_DA_FAIL” → Disable driver signature enforcement on Windows, or try another version of SP Flash Tool.
  • Phone not detected → Ensure the phone is completely powered off (not just screen off). Remove battery (if possible) for 10 seconds.

Q5: My phone is not detected at all. No sound, no driver popup.

A: This indicates a hardware USB port failure on the phone, a completely dead battery, or a damaged charging flex cable. Try a different battery or replace the USB charging port.

Table of Contents

  1. Why You Need the Official Wiko Kite 4G L4020 Stock ROM
  2. Pre-requisites: What You Need Before You Start
  3. Download Links: Official Firmware and Tools
  4. Step 1: Install Wiko Kite 4G USB Drivers
  5. Step 2: Extract and Configure SP Flash Tool
  6. Step 3: Load the Scatter File (The Core of the Installation)
  7. Step 4: Flash the Stock ROM (The Installation Process)
  8. Step 5: First Boot and Initial Setup
  9. Troubleshooting Common Flash Errors (ERROR STATUS_BROM_CMD_SEND_DA_FAIL, etc.)
  10. Frequently Asked Questions (FAQ)
  11. Conclusion

Disclaimer:

Flashing unofficial or incorrect firmware can permanently damage your device. This guide is for educational purposes. Ensure you download the official Wiko Kite 4G L4020 stock ROM from a trusted source. The author assumes no responsibility for any data loss or hardware issues.

Need the direct download link for the official L4020 stock ROM? Check the official Wiko support page or use the model number “L4020” on a reputable firmware repository.

6. Step 3: Load the Scatter File (The Core of the Installation)

The scatter file is a text document that tells the SP Flash Tool exactly where to write each partition (boot, recovery, system, userdata) on the phone’s eMMC chip.

  1. Extract the Wiko_Kite_4G_L4020_Stock_ROM.zip (the firmware file) into a new folder.
  2. Inside, you will find a file named MT6739_Android_scatter.txt or simply scatter.txt (depending on the chipset; Wiko Kite 4G uses MediaTek MT6739).
  3. Go back to SP Flash Tool.
  4. Click the "Scatter-loading" button (usually on the right side of the window).
  5. Navigate to your extracted ROM folder and select the scatter.txt file.
  6. After loading, you will see a checklist with partitions: preloader, md1img, system, cache, userdata, etc.
  7. Verify that all checkboxes are checked except userdata (optional). If you uncheck userdata, your personal files might survive, but for a clean install, keep everything checked.