Pos Printer Driver Setup V11301exe Download Verified ~upd~ May 2026

The POS Printer Driver Setup V11.3.0.1 (often found as v11301.exe) is a universal driver used by many unbranded or "OEM" thermal receipt printers. It is primarily designed to provide ESC/POS communication between Windows systems and thermal printers (typically 58mm or 80mm models). Download & Verification

For security, you should prioritize downloading drivers from the manufacturer's official support portal rather than third-party mirrors.

Official Sources: If your printer has a brand name (e.g., Posiflex, POS-X, or Xprinter), visit their specific download pages.

Verification: Ensure the file version is 11.3.0.1. This version was released around September 2023 and is compatible with Windows 7 through Windows 11. Installation Guide

Connect Hardware: Plug your printer into a USB port and turn it on. pos printer driver setup v11301exe download verified

Run Installer: Open v11301.exe. If prompted by Windows for permission, select "Yes".

Select Printer Type: Choose between POS-58 (58mm paper) or POS-80 (80mm paper) based on your hardware.

Configure Port: The installer might default to a Parallel (LPT1) port. You must manually select the USB port (e.g., USB001) during or after setup to ensure it prints.

Test Print: After installation, go to Settings > Printers & Scanners, right-click your printer, and select Print Test Page to verify the connection. Common Troubleshooting Thermal Receipt Printer Driver - POS-X The POS Printer Driver Setup V11

1. Downloading the Driver

  • From the Manufacturer's Website: The safest way to download drivers is directly from the printer manufacturer's official website. Look for a "Support" or "Downloads" section.
  • Search for Your Model: Enter your printer model number into the search bar on the website.
  • Select Your Operating System: Make sure to select the correct operating system your computer is using (Windows, macOS, Linux, etc.).
  • Find the Driver: Look for the driver version 1.13.01 (or close to it, if available) and click on it to start the download.

Error 3: Printer prints gibberish (raw text/escape codes)

Cause: The POS software is sending raw ESC/POS commands, but Windows is using a text-only driver.

Fix:

  • Open Control Panel → Devices and Printers.
  • Right-click your POS printer → Printer Properties → Advanced.
  • Change Driver to "Generic / Text Only" OR "EPSON ESC/POS Driver V3" (depending on software).
  • Alternatively, enable "Raw mode" in your POS software settings.

Installation Steps

Step 1: Run as Administrator Right-click pos printer driver setup v11301exe and select Run as Administrator. Do not simply double-click.

Step 2: Accept the Security Warning If Windows SmartScreen appears, click "More info" then "Run anyway" – only if you have verified the digital signature in Part 2. From the Manufacturer's Website: The safest way to

Step 3: Choose Installation Mode

  • Typical Install (Recommended): Installs drivers for USB and Serial.
  • Custom Install: Use this if you need Ethernet (LAN) printing. Check the box for "Network Support".

Step 4: The "V11301" Kernel Patch During the install, you may see a dialog box: "Install POS Printer Kernel Mode Driver v1.13.01?" Click Yes. This installs the posprnt.sys file that allows raw ESC/POS commands.

Step 5: Port Selection After the driver installs, go to Control Panel > Devices and Printers.

  • Right-click the "POS Printer" icon > Printer Properties > Ports.
  • USB: Select "USB001 (Virtual printer port for USB)".
  • Serial: Select "COM1" and then click "Configure Port" – set Baud rate to 9600 (or as per your printer spec).
  • Ethernet: Select "Standard TCP/IP Port" and enter the printer's IP address.

Step 6: Test Print

  • Right-click the printer > Printer Properties > General > Print Test Page.
  • For a proper POS test, open Notepad, type "Test Print v11301", and print. The printer should cut the paper automatically if the driver is correct.

Prerequisites:

  • Admin rights on the Windows POS machine.
  • Disable antivirus temporarily (only if you trust the verified source; re-enable immediately after).
  • Disconnect the POS printer from the USB port (reconnect when prompted).

Error 1: "The driver is unsigned" (Windows 10/11)

  • Cause: Microsoft changed driver signing requirements after 2019.
  • Fix: Restart Windows into "Disable Driver Signature Enforcement" mode.
    • Shift + Restart > Troubleshoot > Advanced Options > Startup Settings > Restart > Press F7.

Option 1: Official Manufacturer Websites (Best)

Since v11301 is a generic POS driver standard, it is often released by:

  • Epson ePOS-Print API: Visit Epson’s official download center and search for "TM-T88V driver" or "Advanced Printer Driver". Look for version 5.12 or higher (the internal version may map to v11301).
  • Bixolon Tech Support: Go to Bixolon’s global site → Support → Drivers → Select SRP-330/350 → Look for "Unified POS Driver version 1.13.01".
  • Star Micronics: Navigate to Star's "Software & Drivers" → "StarPRNT" utility. Version 3.13 sometimes uses the v11301 enumeration.