Renolink 1.87 Install Windows 10 May 2026

Renolink 1.87 Install Windows 10 May 2026

Installing Renolink 1.87 Windows 10 involves a few specific driver configurations and file placements to ensure the software communicates correctly with your OBD2 interface. Installation Steps Driver Installation (FTDI) Locate the CDM21218_Setup driver within your Renolink 1.87 folder. Run the setup and follow the prompts to install the FTDI Device Driver

. This is critical for the computer to recognize the OBD2 cable. Software Setup renolink_setup87 installer. Choose your destination folder (typically C:\Program Files\Renolink ) and complete the installation. File Activation renolink.dat executable from your source folder. Paste these directly into the installation directory at C:\Program Files\Renolink , overwriting any existing files if prompted. COM Port Configuration Connect your Renolink interface to your laptop's USB port. Device Manager and find the USB Serial Port under "Ports (COM & LPT)". Right-click the port -> Properties Port Settings COM Port Number (or the port specified by your software version). Change the Latency Timer (msec) to ensure stable communication with the vehicle's ECU. Key Features of v1.87 ECU Programming : Clear crash data, program keys, and read/write EEPROM. Broad Compatibility

: Works with various Renault and Dacia models, including older platforms like the Laguna and newer ones like the Captur. System Access

: Provides full diagnostics for ABS, Airbags, Transmission, and Infotainment modules. Renolink 1.87 Install Windows 10

For more detailed guidance on specific features, you can refer to the Renolink Software User Manual or check for official updates on Renolink.store Are you planning to use this for key programming clearing crash data , as the setup steps for those specific tasks can vary?

Original Renolink Software v2.14 Renault & Dacia Diagnostics

Step 2: Install FTDI Drivers Manually

Renolink interfaces use the FTDI chip. Windows 10 may auto-install generic drivers, but they often conflict. Installing Renolink 1

  1. Extract FTDI_Drivers.zip.
  2. Plug in your Renolink interface (LED should blink once).
  3. Open Device Manager (right-click Start button).
  4. Look for "USB Serial Port (COMx)" under Ports (COM & LPT). It may show as an unknown device with a yellow exclamation.
  5. Right-click → Update driver → Browse my computer for drivers.
  6. Point to the extracted FTDI folder.
  7. Choose "Install this driver software anyway" if warned.
  8. Note the COM port number (e.g., COM4).

Step 2: Disable Driver Signature Enforcement (Windows 10)

  1. Click Start → Power.
  2. Hold the Shift key and click Restart.
  3. After reboot, choose Troubleshoot → Advanced Options → Startup Settings.
  4. Click Restart.
  5. Press 7 or F7 to select "Disable driver signature enforcement".
  6. Windows will now allow unsigned drivers—necessary for Renolink 1.87’s interface.

Important: This setting resets after each reboot. For the installation process, keep your PC in this mode until complete.

Error 2: Driver Installation Fails with "Digital Signature Required"

Cause: Windows 10’s driver enforcement reinstated after reboot. Solution:

  • Reboot and disable driver signature enforcement again (use the Shift + Restart method).
  • Alternatively, use bcdedit command as Admin:
    bcdedit /set testsigning on
    (Reboot, install drivers, then run bcdedit /set testsigning off afterward).

Step 3 – Install USB Drivers

The interface cable is critical:

  • Connect the Renolink OBD interface to the PC.
  • Open Device Manager.
  • Locate the unknown device (usually under "Other devices").
  • Right-click → Update driver → Browse my computer → Point to Drivers folder in the Renolink directory.
  • If using an FTDI chip, install CDM21228_Setup.exe (if provided).

System Requirements for Renolink 1.87 on Windows 10

To ensure a smooth Renolink 1.87 install on Windows 10, your machine should meet the following minimum specifications:

| Component | Requirement | |-----------|-------------| | OS | Windows 10 (32-bit or 64-bit) Pro/Enterprise recommended | | RAM | 4 GB minimum | | Storage | 500 MB free space | | Processor | Intel Core 2 Duo or newer | | Interface | USB 2.0 port (compatible with USB 3.0 but may require driver tweaks) | | Diagnostic Tool | Renolink 1.87 interface (FTDI FT232RL based) |

Note: Windows 10 Home often has more restrictive group policy settings, making driver installation harder. If possible, use Pro or Enterprise. Step 2: Install FTDI Drivers Manually Renolink interfaces

Renolink 1.87 vs. Newer Versions on Windows 10

| Feature | Renolink 1.87 | Renolink 1.95+ | |---------|---------------|----------------| | Windows 10 compatibility | Needs tweaks | Native support | | Renault ZOE (electric) | Limited | Full support | | Key programming | Yes | Yes | | Clone-friendly | Yes (crack available) | Not easily cracked | | Stability | Excellent | Good (requires activation) |

For most hobbyists, version 1.87 remains the best balance of functionality and cost.