Seisimager Registration Password ⇒

For SeisImager software—widely used for seismic data analysis—the registration password is the key to unlocking the full version from its demonstration mode. Depending on your version and how you purchased the software, the process involves either a 12-digit keyword Registration ID 1. How to Obtain Your Registration Password The password is not generic; it is uniquely generated by Geometrics

(the software developer) based on your specific computer or hardware serial number. Initial Installation:

When you first install the software, you will be presented with a 12-digit code (keyword). Requesting the Password:

You must copy this 12-digit code into an email and send it to support@geometrics.com along with your seismograph serial number order number Receiving the Password: The support team will reply with a 40-digit registration password

. Using email is highly recommended to avoid typos in these long strings of characters. SeisImager 2. Where to Enter the Password If you are already running the software in Demonstration Mode , you can register it without reinstalling: Via the Registration Program: Go to the Windows Start menu , navigate to All Programs SeisImager , and open the SeisImager Registration Via the Software Interface:

For some versions (like SeisImager/2D), you can also enter a new password in the Dimension Size dialog box (accessed by holding the

while double-clicking the program icon), though using the standalone registration program is the preferred method. Geometrics 3. Key Differences by Version Older Versions (Pre-May 2021): These typically rely on the keyword and password system described above. Newer Versions (May 2021 and Later): These often use a Registration ID , which can usually be found on your customer invoice. Geometrics Summary Checklist for Registration Generate Code SeisImager Registration program to see your unique 12-digit keyword. Email Support Send the keyword + your Seismograph Serial Number to support@geometrics.com Input Password

Paste the 40-digit response into the password field and click seisimager registration password

If you are upgrading or transferring a license to a new PC, you should consult the License Transfer Instructions to ensure the old license is properly deactivated first. Geometrics specific module

SeisImager uses a two-step "lock and key" system for software activation. Unlike standard software that might use a simple serial key, SeisImager requires a unique password tied to your specific PC hardware.

1. Generating the Keyword/ID: When you first install SeisImager, the software generates a 12-digit code (sometimes called a "Keyword" or "Registration ID") unique to that computer.

2. Requesting the Password: You must email this 12-digit code along with your seismograph serial number or order number to support@geometrics.com.

3. Receiving the Password: Geometrics will reply with a 40-digit registration password that unlocks the full version of the software. Key Takeaways & Tips

Demonstration Mode: You can run the software in "demonstration mode" without a password to explore basic features, but processing and saving capabilities will be restricted.

License Transfers: If you need to move the software to a new computer, you must use the SeisImager Registration program to "Transfer registration to another PC," which deactivates the license on the old machine to free it up for the new one. Install SeisImager

Contact Support Directly: Because the password is hardware-dependent, there is no "universal" password. You must contact Geometrics Support to receive your unique 40-digit key. Review Summary

The SeisImager registration system is highly secure but can be a bit slow for users who need immediate access, as it relies on manual email correspondence with the manufacturer. It is highly recommended to perform this registration well before a scheduled field survey to ensure your software is fully functional when needed. SeisImager/DHTM Manual

To obtain the SeisImager registration password , you must provide specific hardware and purchase information to the software manufacturer, Geometrics , as there is no universal "paper" or fixed password. SeisImager How to Get the Registration Password

The process for receiving your permanent license password depends on the registration method your version uses: Keyword Method

Launch the software. A registration dialog box will appear with a 12-digit keyword Copy this keyword and email it to support@geometrics.com Include your order number (from your invoice) and the serial number of your seismograph. Geometrics will reply with a 40-digit registration password to enable your purchased version. Registration ID Method (Modern Versions) Newer versions typically use a Registration ID found on your PDF invoice or order acknowledgment. If you cannot find it, you can look up your ID on the SeisImager Registration Lookup Page by entering your order number. Demonstration Mode

If you do not have a password yet and want to test the software, you can run it in demonstration mode Open the registration dialog box. Leave the password field

The software will report the number of available trial runs (typically 15). Official Resources the computer cannot read the dongle

For detailed step-by-step instructions, refer to the following official guides: SeisImager/SW User's Manual SeisImager Installation & Registration Guide License Transfer and Registration Instructions order number to complete the registration?

4. Installing a New License (Windows)

1. Install SeisImager.
2. Open the software → Help → Register / License Manager.
3. Enter the registration password provided by Geometrics.
4. If using a license file: copy it to C:\Program Files (x86)\SeisImager\License\
5. Restart the software.

2. Request a Password via the License File Generator

For recent versions, registration is often handled through a license file (*.lic). You will run the software, copy a Host ID (MAC address or hard drive serial), paste it into a web form on the manufacturer’s site, and receive the registration password via email.

How to Properly Register SeisImager

If you have purchased a legitimate license or are a trial user, here is the standard procedure to finalize your registration without running into password errors.

How to Enter the SeisImager Registration Password Correctly

Entering the password incorrectly is the #1 cause of activation failure. Follow this ritual precisely:

1. Run as Administrator: Right-click the SeisImager executable and select Run as administrator. Registry writes required for permanent storage.
2. Copy, Don’t Type: Use Ctrl+C to copy the password from the email and Ctrl+V into the registration field. Avoid manual typing: 0 (zero) vs O (letter) and 1 vs I are common pitfalls.
3. Case sensitivity: Some versions are case-sensitive. Use exactly as provided.
4. Module selection: If prompted, select the correct module (e.g., "SeisImager SW"). A password for the SW module will not unlock the SE module.
5. Click Register/OK: The software will typically restart. Check: Help > License Info should now show "Licensed to: [Your Name]" and no expiration (or a future date).

Step 2: Contact Your Distributor

You cannot generate the password yourself. You must send the fingerprint to:

• Geometrics Inc. (if purchased directly) – support@geometrics.com
• OYO Corporation (for older Japanese versions)
• An authorized local distributor (e.g., Geomatrix, TerraDat).

Provide the following information in your email:

• Full software name (e.g., "SeisImager SW v3.35")
• Fingerprint string
• Purchase order number or license entitlement ID
• Module(s) you need unlocked (SW, SE, TOMO)

Step-by-Step: Entering Your Registration Password

Assuming you have a valid password, here is the standard activation workflow for SeisImager (Windows 10/11):

1. Install the Software: Run Setup.exe as Administrator.
2. Launch SeisImager: The “License Manager” dialog appears upon first launch.
3. Enter User Info: Type your name, company, and email (must match the purchase record).
4. Input Password: Carefully type the SeisImager registration password – note that it is case-sensitive and often includes hyphens.
5. Hardware Key Check: If using a USB dongle, ensure it is inserted before clicking “Activate.”
6. Confirmation: You will see “License Activated Successfully.” Restart the software.

Final Checklist: Before You Contact Support

If you still cannot get the registration password to work, gather this information before emailing your distributor:

• [ ] Screenshot of the error message.
• [ ] SeisImager version (Help > About).
• [ ] Your Windows version and architecture (32-bit vs 64-bit).
• [ ] Dongle serial number (printed on the physical key).
• [ ] Proof of purchase (invoice number).
• [ ] The exact Host ID from the License Manager.

Step 2: Install the Driver (For Dongle Users)

If you are using a USB dongle, ensure you have installed the correct "Sentinel" or "HASP" driver. Without this driver, the computer cannot read the dongle, and the software will assume it is unregistered.

• Tip: These drivers are usually found in the "Drivers" folder on the installation CD or the downloaded ZIP file from the official website.