The installation of a ThyssenKrupp Levant stair lift (also known as the Comfort or Homeglide in some markets) is designed to be completed within a few hours and requires mounting the track directly to the stairs rather than the wall.

The full installation manual typically covers the following key stages: 1. Preparation and Site Inspection

Component Verification: Ensure all rail elements, the lift unit, and hardware are present and undamaged.

Site Clearance: Clear the staircase of all obstructions and measure the rail path to ensure the track will extend properly beyond the bottom step to the floor. 2. Rail Installation

Sequential Assembly: Connect rail sections in the order specified by the installation drawing using provided screws and brackets.

Wiring Integration: Pull the electrical wiring through the rail during assembly to connect charging points.

Securing the Track: Fasten the rail securely to the stair steps. If installing on carpet, screws must penetrate through to the wood or concrete beneath. 3. Drive Unit and Electrical Setup

Mounting the Lift: Attach the drive unit to the rail end. The Levant features a unique silver track and a wraparound seat.

Power Connection: Connect the transformer to the charging contacts nearest a wall socket. The system typically operates at approximately 33 V.

Battery Installation: Ensure the internal sealed lead-acid batteries are correctly seated and the terminals are clean to prevent corrosion. 4. Testing and Commissioning

Operational Check: Test the lift using the armrest joystick to move in both directions.

Safety Sensors: Verify that the safety edges on the footrest and drive unit stop the lift immediately upon contact with an obstacle.

Call/Send Stations: Test the wireless remote units to ensure they can call the chair from either end of the track. Manual Resources

Because ThyssenKrupp Access no longer manufactures these products in the U.S., finding the specific Installation Manual can be difficult through official channels. However, resources are available at:

Digital Archives: View the Levant User Manual for free on Manua.ls.

Third-Party Parts Sites: The specific Installation Manual is often sold by specialist retailers like Access2Parts. Levant stairlift User Manual

Comprehensive Guide: ThyssenKrupp Levant Stair Lift Installation Manual

The ThyssenKrupp Levant stair lift (now often branded under TK Elevator or S200) is celebrated for its simplicity, reliability, and DIY-friendly design. If you have acquired a Levant—whether new or pre-owned—having a clear roadmap for installation is essential for both safety and functionality.

This guide serves as a comprehensive overview of the installation process, mirroring the technical specifications found in the official installation manual. 1. Pre-Installation Checklist

Before unboxing, ensure your staircase is compatible with the Levant’s specifications.

Staircase Type: The Levant is designed for straight indoor staircases only.

Clearance: Ensure a minimum staircase width of 28–30 inches.

Power Source: A standard 110V AC outlet must be available near the top or bottom of the stairs to plug in the battery charger. Tools Required: Power drill with masonry or wood bits. Socket wrench set (13mm and 17mm are common). Allen key set. Spirit level and tape measure. 2. Component Overview Your Levant shipment should include: The Drive Unit (Chassis): The motor and battery housing. The Chair: Including the seat, armrests, and footrest. The Rail Sections: Usually two or three aluminum segments.

Charging Stations: Located at the top and bottom of the rail. Remote Controls: Two wireless units. Installation Kit: Brackets (feet), bolts, and screws. 3. Step-by-Step Installation Process Step A: Assemble the Rail

Lay out the rail segments on the stairs to check the length. If the rail is too long, it can be cut from the bottom end using a circular saw with a metal-cutting blade.

Join the sections: Slide the internal joint pins into the rail channels and tighten the joining bolts until the rail is a single, rigid piece.

Position the rail: Place the rail on the steps, ensuring a gap of approximately 5 inches (12 cm) between the rail and the wall. Step B: Secure the Mounting Brackets Attach the feet: Slide the mounting brackets onto the rail.

Leveling: Use a spirit level to ensure the rail is consistent.

Fastening: Screw the brackets into the stair treads. For wood stairs, use the provided wood screws; for concrete, use masonry anchors. Step C: Mounting the Drive Unit

Safety First: Ensure the "on/off" switch on the chassis is in the OFF position.

Slide onto rail: Carefully slide the drive unit onto the rail from the top or bottom (depending on your model’s specific entry point).

Install End Stops: Immediately bolt the mechanical end stops at both ends of the rail to prevent the lift from over-traveling. Step D: Install the Seat Place the seat assembly onto the drive unit’s post.

Secure the locking bolt and connect the communication cable (usually a multi-pin plug) that links the seat controls to the main chassis. Step E: Electrical and Charging

Install Charge Strips: Ensure the copper charging strips at the top and bottom of the rail are clean and aligned with the "brushes" on the drive unit.

Connect the Transformer: Plug the transformer into your wall outlet and run the low-voltage wire to the rail’s charging point. 4. Calibration and Testing Once assembled, turn the unit on.

Battery Charge: Allow the unit to charge for at least 4–6 hours before the first full-weight test.

The "Dry Run": Run the lift up and down using the armrest toggle without a passenger. Listen for any clicking or resistance.

Safety Sensors: Gently press the edges of the footrest and the chassis. The lift should stop immediately if it hits an obstruction. 5. Maintenance and Troubleshooting

Lubrication: The Levant uses a dry-rail system. Do not apply grease to the rail; instead, keep it clean and free of dust.

Beeping Sounds: Constant beeping usually indicates the lift is not parked on a charging point.

Battery Replacement: Generally required every 3–5 years depending on usage. Safety Warning

While many homeowners successfully install the ThyssenKrupp Levant themselves, local building codes may require a licensed technician for inspection. Improper installation can void warranties and pose a significant fall risk. If you encounter resistance or are unsure about the structural integrity of your stairs, consult a professional.

3. Tools and Materials Required

• Cordless drill and bits (metal and wood)
• Torque wrench and sockets
• Hex/Allen key set
• Screwdrivers (Phillips and flat)
• Spirit level and plumb line
• Measuring tape, marker, masking tape
• Hacksaw or circular saw with metal blade (for cutting rail)
• File or deburring tool
• Multimeter
• Cable ties, insulation tape
• Anchor bolts (as per substrate) and rawl plugs
• Thread-locking compound
• Manufacturer-supplied fixings and electrical harnesses

Step 2 – Mount Wall Brackets

• Mark bracket positions on wall (aligned with studs or solid masonry).
• Drill pilot holes. For drywall over studs: use lag bolts. For masonry: use anchor bolts.
• Attach brackets to wall, leaving them slightly loose for rail alignment.

Overview of ThyssenKrupp Levant Stair Lift

The ThyssenKrupp Levant is a type of stair lift designed to help individuals with mobility issues navigate stairs safely and easily. It's known for its reliability, comfort, and sleek design.

Step 6 – Safety Features Check

• Swivel seat sensor (prevents operation if seat not locked).
• Obstruction sensors (under footrest and at carriage base).
• Manual lowering valve (for power outage).

Full Review: Thyssenkrupp Levant Stair Lift Installation Manual

Installation Manual

For a full installation manual, here are a few steps you can take:

1. Contact ThyssenKrupp or a Local Dealer: The most reliable source for a comprehensive installation manual would be ThyssenKrupp itself or a local authorized dealer. You can visit their official website, find the contact information for your region, and request a manual.

2. Manufacturer's Website: Sometimes, manufacturers provide downloadable manuals or guides on their official websites. You can check the ThyssenKrupp (now part of thyssenkrupp Home Solutions) website for resources.

3. Online Forums and Communities: Websites like Reddit, home improvement forums, or mobility aid forums might have users who have installed similar models. They might be able to provide tips, share their experiences, or direct you to where you can find the manual.

4. Professional Installation: While having a manual is helpful, it's also important to consider professional installation. Stair lift installation can be complex and requires ensuring safety and proper functionality.

Executive Summary

The thyssenkrupp Levant is widely regarded in the industry as a robust, "workhorse" straight stair lift. The installation manual reflects the engineering philosophy of the unit: it is modular, rack-and-pinion driven, and designed for quick installation with minimal structural modification to the home.

Verdict: The manual is technician-focused. It is highly logical and diagram-heavy but assumes the user has a baseline knowledge of stair lift mechanics. It is not a "DIY-friendly" guide for the average homeowner.

Part 3: Drive Unit Installation & Wiring