Product/Service: Assuming TS1162 is a piece of technical equipment, possibly related to telecommunications or electronics.
Review: "The TS1162 Installation Manual provides a comprehensive guide to setting up the equipment. The document is generally well-organized, but could benefit from clearer visual aids to assist in the understanding of complex installation steps. The technical details seem accurate and up-to-date. However, additional troubleshooting tips and a detailed FAQ section would enhance the manual's value to the end-user. Overall, it serves as a good foundation, with some areas for improvement to make it more user-friendly and comprehensive."
The Tecom TS1162 is a 3 LED Remote Arming Station (RAS) keypad designed for the Challenger security system. It is frequently used in environments requiring robust construction, such as dusty or wet locations, due to its IP67 rating. 1. Key Specifications
Connectivity: Connects directly to the Challenger RS-485 LAN.
Operating Range: Can be installed up to 1.5 km from the main Challenger panel or Intelligent Access Controller. Inputs/Outputs: One input for Request to Exit (RTE) control.
One open collector output for controlling door relays or strikes.
Durability: Robust molded plastic housing suitable for indoor or outdoor mounting. 2. General Installation Steps While specific detailed
manuals are often restricted to authorized installers, the procedure follows standard Tecom RAS installation protocols as seen in similar models like the TS1001:
Preparation: Power down the Challenger panel before beginning any wiring.
Disassembly: Remove body retaining screws and separate the body from the base. Mounting:
Use the provided template to mark mounting holes and cable entry points.
Ensure the tamper lever will be fully depressed once mounted to avoid false tamper alarms.
Secure the base to the wall using appropriate screws for the surface type.
Addressing: Use the internal DIP switches (typically switches 1–4) to set the unique RAS address on the LAN. ts1162 installation manual
Termination: If this is the last device on the RS-485 LAN, set the LAN termination DIP switch (usually switch 8) to ON. Wiring: Terminate the LAN cabling (+, –, D+, D–). Connect the RTE input and door relay output if required.
Reassembly: Hook the top of the body onto the base tabs and secure with the bottom retaining screws. 3. Support and Documentation
For the full technical manual, installers can access the Aritech/Tecom Support Portal.
Manuals Library: Official documents are hosted on the Aritech Support Site.
Authorized Access: Note that some detailed installation and programming manuals are restricted to trained installers with valid login credentials. Tecom Manuals - Kidde Global Solutions Support
TS1162 Installation Manual: A Comprehensive Setup Guide The TS1162 is a high-performance industrial component known for its reliability and precision. However, its effectiveness depends entirely on correct installation. This manual provides a step-by-step walkthrough to ensure your unit is mounted, wired, and configured for peak performance. 1. Pre-Installation Checklist
Before beginning the process, ensure you have the following tools and environment ready:
Tools Required: Metric hex key set, precision screwdriver, digital multimeter, and wire strippers.
Environment: Ensure the installation area is dry, vibration-free, and within the operating temperature range (typically -10°C to 50°C).
Unboxing: Inspect the TS1162 for any shipping damage. Verify that the package includes the main unit, mounting brackets, and terminal connectors. 2. Mechanical Mounting
The TS1162 supports both DIN-rail mounting and panel mounting. DIN-Rail Installation: Tilt the unit slightly backward.
Hook the top slot of the TS1162 onto the upper edge of the DIN rail.
Push the bottom of the unit toward the rail until the spring-loaded clip snaps into place. Gently tug the unit to ensure it is securely seated. Panel Mounting: TS1162 Installation Manual 4
Use the provided template to mark the drill holes on your panel. Secure the mounting brackets to the sides of the TS1162.
Fasten the unit to the panel using M4 screws, ensuring a torque of 1.2 Nm. 3. Wiring and Connectivity
Proper wiring is critical to prevent electrical interference and hardware damage. Ensure all power sources are turned off before making connections.
Power Supply: Connect the DC power source (check your specific model for 12V or 24V requirements) to terminals V+ and V-. Always use a grounded power supply.
Input/Output (I/O): Strip wires to approximately 7mm. Insert them into the terminal block and tighten the screws. Ensure there are no stray strands that could cause a short circuit.
Communication Ports: If using the RS-485 or Ethernet interface, use shielded twisted-pair cables to minimize EMI (Electromagnetic Interference). 4. Initial Configuration
Once the hardware is secure and wired, follow these steps for the first boot:
Power On: Apply power and watch the LED indicator. A steady green light typically indicates the system is ready.
Interface Setup: Access the configuration menu via the onboard display or the connected software utility.
Parameter Entry: Input your specific operational parameters (baud rate, IP address, or setpoints) as dictated by your project requirements. 5. Troubleshooting Common Issues
No Power: Check the polarity of the DC input and verify the fuse integrity.
Signal Noise: Ensure the unit is properly grounded and that signal cables are kept away from high-voltage power lines.
Error Codes: Consult the "Error Code Table" in the appendix of your physical manual for specific flashing patterns on the LED. Maintenance and Safety Temp/RH Probe: At canopy level (plants) or 5
Safety First: Never open the TS1162 casing while power is applied.
Cleaning: Use a dry, anti-static cloth to remove dust from the vents to prevent overheating.
By following this manual, you ensure the longevity and accuracy of your TS1162 unit. For advanced programming or specific application diagrams, refer to the manufacturer’s technical data sheets.
Tecom TS1162 is a robust 3-LED Remote Arming Station (RAS) keypad used primarily with Challenger security systems. Because detailed installation and programming manuals for Tecom hardware are often restricted to trained installers, they can be difficult to find on public websites. support.firesecurityproducts.com.au Key Technical Details for Installation
If you are looking for specific configuration steps, the following details are essential for the TS1162: Wiring & Connection
: The keypad connects directly to the Challenger RS-485 LAN and can be situated up to from the main panel or Intelligent Access Controller. Addressing : You must use DIP switches 1 through 4 on the unit to set its unique RAS address. Inputs & Outputs : Features a dedicated input for a Request to Exit (RTE) sensor or push-button. Open Collector Output
: Includes an output that can control a door strike or relay. Environment : It is rated , making it suitable for wet or dusty environments. Ness Corporation Official Documentation & Support Aritech/Tecom Support Portal
: The most reliable "article" and source for the full manual is the Tecom Manuals page
on the Kidde Global Solutions support site. Note that full installation and programming guides may require a dealer login Product Datasheet
: You can find a high-level overview and technical specifications on the Aritech official product page Common Default Codes : For initial setup on Challenger V8 systems, the default installer code aritech.com.au specifically, or do you need help programming the keypad's address? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED - Aritech. Skip to: aritech.com.au Tecom Manuals - Kidde Global Solutions Support 14 Nov 2025 —
| Parameter | Day (06:00–22:00) | Night (22:00–06:00) | |-----------|-------------------|----------------------| | Heat Setpoint | 74°F | 67°F | | Cool Setpoint | 76°F | 69°F | | Hysteresis | ±1°F | ±1.5°F |