To reset the password for a Traice DVR, you typically need to use a dynamic password generated based on the system's current date or its serial number. Since "Traice" is often a rebranded or white-label OEM product (frequently using XMeye or Dahua firmware), the most reliable recovery methods involve software-based super passwords or physical hardware resets. Method 1: Dynamic Super Password (Recommended)
Most Traice-compatible systems use a "Super Password" based on the internal system date.
Check the DVR Date: Look at the date and time displayed on your monitor (e.g., 2026-04-16).
Generate a Code: Use a standard DVR password generator. For many XMeye/Traice boards, codes are generated based on YYYYMMDD.
Common Universal Codes: Try default combinations like 000000, 111111, 123456, or 888888 first [23].
Enter the Code: Type the generated super password into the login screen. This should bypass the user lock and allow you to set a new admin password. Method 2: Serial Number Recovery
If the date method fails, you can use the device's unique serial number.
Locate the Serial Number: Go to the login screen and click "Forgot Password" or look for an information icon. Note the Serial Number (S/N) or Device ID [18].
Contact Support: If you cannot find a generator tool (like GenSuperPassword.exe), you may need to take a photo of this screen and email it to the manufacturer or your local distributor to receive a one-time unlock code [24]. Method 3: Physical Hardware Reset
If software methods are unavailable, a manual factory reset is required.
Motherboard Reset Button: Open the DVR casing and look for a small push-button labeled "RESET" or "SW1" on the motherboard. With the power off, hold the button, plug the power in, and keep holding for 15–30 seconds [4, 21].
CMOS Battery Removal: Unplug the power and remove the round silver battery (CR2032) from the motherboard for at least 3 minutes. This often reverts the system date to a factory default (e.g., 2000-01-01), which allows you to use a known default password for that specific date. Summary of Common Default Credentials Brand/Firmware Default Username Default Password Traice / XMeye admin (blank) or 123456 Dahua OEM admin admin Hikvision OEM admin 12345 or password
Important Note: Performing a factory reset may erase your network settings and recording schedules, but it typically does not delete recorded footage on the hard drive [19, 22].
The following story illustrates a typical scenario for resetting a Traice DVR (often rebranded or similar to common H.264 network DVRs) when a password is lost. The Locked Lens: A Reset Story traice dvr password reset
Marcus sat in his small office, staring at the login screen of his Traice DVR. It had been months since he last needed to check the footage, and the password he thought he knew—a combination of his old dog’s name and birth year—wasn't working. After three failed attempts, the system began to mock him with "Account Locked."
He knew he had two options: the "Soft Reset" via the interface or the "Hardware Reset" involving the machine's guts. The Digital Key Search
First, Marcus tried the digital route. He clicked on "Forgot Password". The screen popped up with a Serial Number and the current system date. He remembered reading that some technicians use a "Super Password" generator. He grabbed his phone and searched for a DVR password calculator.
By entering the date displayed on the DVR (which had drifted back to 2000-01-01), the tool gave him a temporary six-digit code. He held his breath and typed it in. Invalid. The Traice firmware was newer than the old calculator could handle. The "Battery" Trick
Determined, Marcus grabbed a screwdriver. He unplugged the power, unscrewed the casing, and peered inside. There, nestled on the green motherboard, was a small, silver CMOS battery. He carefully popped the battery out using a small flathead.
He waited for a full minute to let the internal capacitors drain. He reinserted the battery and plugged the power back in.
As the DVR chimed to life, the date had reset to the factory default. He tried the classic default login: Username admin with a blank password, or sometimes 12345. This time, the menu opened. Success and Security
Marcus immediately went to the Account Settings. He didn't want to do this again, so he created a new, strong password and, more importantly, took a photo of the recovery QR code provided by the system for future resets. He closed the metal casing, tightened the screws, and finally watched the footage he needed. Common Reset Methods for DVRs
If you are currently facing a lockout with a Traice or similar DVR, these are the most reliable methods:
Default Passwords: Try admin (blank), 123456, 888888, or 000000.
CMOS Battery Removal: Unplugging the internal battery for 1-5 minutes often resets the system clock and password to factory defaults.
Hardware Reset Button: Look for a small "Reset" button on the motherboard. Hold it for 15 seconds while powering the unit on.
Super Password Generators: Use the serial number and the date shown on the monitor to generate a one-day master code via support sites. To reset the password for a Traice DVR
Resetting a Traice DVR password typically involves using a master password based on the current date, utilizing a physical reset button on the motherboard, or using specialized password generator software for unbranded H.264 systems. Top Recovery Methods
If you have forgotten your admin credentials, try the following methods in order:
There is no single "universal backdoor password" for Traice DVRs. The method depends on the device’s firmware version and age. The following methods are standard in the industry and apply to most H.264/H.265 DVRs, including Traice.
Forgetting the password to your security system is frustrating. You might need to add a new camera, adjust recording schedules, or simply view playback, but you are locked out of the admin menu.
This article covers every method to reset a Traice DVR password, from default codes to factory resets.
Before attempting advanced resets, try these combinations (case-sensitive, no spaces):
| Model Series | Username | Password |
| :--- | :--- | :--- |
| Traice 4/8/16-Ch (2015-2018) | admin | (leave blank) |
| Traice 4/8/16-Ch (2018-2020) | admin | 12345 |
| Traice 1080N Series | admin | 123456 |
| Traice 5MP / 4K Series | admin | 12345abc |
| Traice OEM (Hikvision clone) | admin | 12345 or 111111 |
| Traice OEM (Dahua clone) | admin | admin |
Before opening the case or calling a technician, test these common default credentials. Many Traice units ship without a unique password set.
Username: admin
Password: 12345 or 123456
Username: admin
Password: admin (leave blank)
Username: 888888
Password: 888888
Username: 666666
Password: 666666
Pro Tip: If the DVR is used or installed by a company, the password may be changed to 000000 or the installer's phone number.
| Method | Success Rate | Difficulty | | :--- | :--- | :--- | | Default passwords | 40% | Easy | | Forgot Password / Reset code | 50% (if feature exists) | Medium | | Physical reset button | 80% | Medium | | Serial port (TTL) | 95% | Hard | | Contact support | 70% | Easy |
If all else fails: Replace the DVR. A basic 4-channel Traice-style DVR costs less than $50, which is often cheaper than a professional unlock service.
Need further help? Reply with the exact model number printed on your Traice DVR’s circuit board or back sticker for model-specific instructions.
To reset the password on a Traice DVR , you can use several methods depending on whether you have physical access to the device or can use software-based recovery tools. 1. Try Default Credentials
Before performing a hard reset, try the standard factory default passwords for Traice and generic H.264 DVR systems: Username: admin Password: 123456, admin, 1234, or leave it blank. 2. Physical Hardware Reset
If you are locked out, a physical reset on the motherboard is often the most reliable method.
Reset Button: Many models have a small physical reset button on the back or inside on the motherboard. Press and hold it for 10–30 seconds while the unit is powering on.
Jumper Pins: Look for two metal pins on the motherboard (often labeled TP1, J1, or JP1). While the DVR is off, use a screwdriver or tweezers to connect these pins. Keep them connected, power on the device, and wait about 60 seconds before releasing them.
CMOS Battery Removal: Unplug the DVR and remove the small CR2032 button cell battery from the motherboard for a few minutes. This can sometimes reset the system clock to a default date (like 2000-01-01), which is useful if you are using a super password generator. 3. Software & Super Password Generators On-device password recovery options (safest) Web UI /
If your DVR displays a Serial Number or a specific system date on the login screen, you can generate a one-time "Super Password." How to Reset DVR Password
BPP Marcin Borkowski
ul. Architektów 14
05-270 Marki
Poland
Mobile +48 606725871
©2005 - 2022 ChemBuddy